Eleaf iKonn 220 TC Box Mod

item image
Facebook Twitter GooglePlus Pinterest

GearbestÁr 40.63 USD

  • What kind of screen does Eleaf iKonn 220 ELLO TC box mod adopt?

    OLED screen.

  • Can i upgrade the firmware of iKonn 220 ELLO TC box mod?

    Yes, you can.

  • How to turn on / off it?

    Pushing forward to open the battery cover, put two high-rate 18650
    batteries in correct way into the device and finally close the battery cover. The device can be powered on or off by pressing the fire button 5 times. The battery levels of battery 1 and battery 2 are respectively displayed on the screen.

  • Can i shift between the °C and ˚F?

    Yes, you can.

  • How to charge my phone via it?

    Screwing an RC adapter (not included) on the device and connect it with a cell phone by a USB cable. When the device is powered on, press the fire button once to start to charge the cell phone.

  • Can i rotate the screen?

    Keep pressing “+” end and “-” end simultaneously for two seconds when the device is powered off, the screen display will rotate 180 degrees. You can view the screen from two different angles through this operation.

  • How to switch the vaping mode?

    When the device is powered on, press the fire button 3 times in quick succession, the device will display current vaping mode. Press the
    “+” or “-” end to switch among VW, USB Charge (this mode appears only when “USB” is on), TC-Ni, TC-Ti, TC-SS, TCR-M1, TCR-M2, TCR-M3 modes and then press the fire button once or stay in the interface for about 10 seconds to confirm the vaping mode you chose.

  • How to charge Eleaf iKonn 220 ELLO TC box mod?

    The battery power indicator on the screen of the device will keep flashing when the remaining power of the 18650 batteries is less than 10%. The 18650 batteries can be charged in the device through USB port via wall adapter or a computer or charged with an external battery charger. If the 18650 batteries are charged in the device, the battery bars on the screen will keep flashing during charging and the screen will go out when fully charged.

  • How to use the preheat function?

    In power-off state, keep holding “+” end and fire button till the
    M1 mode appears; press the fire button 3 times to “Power”, and press “+” or “-” end to adjust the wattage of preheat; press the fire button again to “Time”, and press “+” or “-” end to adjust the second of preheat or to turn off the preheat function.

  • Why it display “check battery”?

    If the batteries are installed incorrectly, the screen will display “Check Battery”.

  • What if the device keeps showing “Check Battery” “Low Battery” “Weak Battery”?

    We suggest you change to another set of batteries first. It is recommended to use high-rate batteries.

  • Why does the device always go back automatically to the VW mode from TC mode?

    Please make sure that your resistance is correct, otherwise, the device will detect itself and will be allowed to be used only in VW mode. You can also try to take out the atomizer and switch to TC mode in room temperature.

  • Why does the device always show “Device too hot” when I press the fire button?

    Please let the device cool down for a while. The higher the wattage, the bigger the current, so as the temperature, causing more heat. You can try to use TCR mode and set the TCR value according to your coil’s material. If the value is not correct, the device will detect itself and give a wrong judgment and output.

  • Why does the LED start flashing while using?

    It means that you have to charge the battery.

  • What if the device can’t turn on after charging?

    Put a new battery in it then turn on. If the device support upgrade, you can try as follows:

    1. Take out the batteries;

    2. Plug on the USB to connect to your computer;

    3. Open the software on the computer to upgrade.

  • How to maintain the vapor device?

  • What is the meaning of “charge error” dispalying on the screen?

  • How to choose the right battery for your VV / VW mod?

  • What are the factors will affect lifespan of coil head?

  • Can this item be shipped to my country?

  • Why the screen display “Check Atomizer”?

    The DNA does not detect an atomizer, the atomizer has shorted out, or the atomizer resistance is incorrect for the power setting.

  • Why the screen display “Weak battery”?

    The battery is deeply discharged and needs to be charged, or is damaged.

  • Why the screen display “Shorted”?

    The atomizer or wiring are short circuited.

  • Why the screen display “Ohms too Low or high”?

    The resistance of the atomizer coil is too low or high for the current wattage setting.

  • Can this item be shipped to my country?

  • How to catch the best price on GearBest?

  • How many payments does GearBest support?

    4 available GearBest payment methods for your easier shopping

  • How to cancel the order on GearBest?

  • Price: 40.63


    Ez is érdekelhet

    Authentic Iwodevape E-Cig Vapeband Silicone Ring DIY Decorative Ring Color Random Color Delivery

    Authentic Iwodevape E-Cig Vapeband Silicone Ring DIY Decorative Ring Color Random Color Delivery

     Megnézem    GearbestÁr 2.15 USD 1. Beautifully designed, a variety of colors2. Using food grade silicone, …

    Vélemény, hozzászólás?

    Ez a weboldal az Akismet szolgáltatását használja a spam kiszűrésére. Tudjunk meg többet arról, hogyan dolgozzák fel a hozzászólásunk adatait..

    Copy Protected by Chetan's WP-Copyprotect.

    Nem találtál választ? Tedd fel a kérdésed!

    You will get a notification email when Knowledgebase answerd/updated!

    + = Verify Human or Spambot ?